Chi tiết sản phẩm

Bộ hiển thị momen quay - TM301 (Unipulse Việt Nam)

Mã sản phẩm :
Giá bán : Liên hệ
Xuất xứ : Nhật Bản
Tình trạng hàng hóa : mới 100%
Thời gian bảo hành : 12 Tháng
Mô tả : Bộ hiển thị TM301 dùng cho cảm biến momen quay UTM II, UTMV. Nhà sản xuất: Unipulse - Nhật Bản.

* Bộ hiển thị mômen dùng cho cảm biến UTM II/UTMV
* Mômen, tốc độ quay và công suất được hiển thị đồng thời
* Chức năng giữ (Mẫu, Đỉnh lồi, đỉnh lõm, P-P, giá trị trung bình)
* Chức năng so sánh trên/dưới (ALM HI, HI, OK, LO, ALM LO)
* Chức năng lưu dữ liệu
* Dễ dang kết nối với cảm biến UTM II/UTMV với một sợi cáp
* Nguồn vận hành có thể cấp cho cảm biến UTM II/UTMV 
* Sự biến đổi của mômen, rpm, và công suất có thể được giám sát và lưu trên máy tính (chỉ với tùy chọn giao tiếp USB )

 

Sensor input for torque (voltage input)
Input resistance 1MΩ
Signal input range ±5V
Accuracy Non-linearity:Within 0.02%/FS±1digit
Zero drift:Within 0.2mV/℃ RTI
Gain drift:Within 0.01%/℃
A/D converter ・ Speed…300 times/sec.
・ Resolution…24bit(binary) Approx. 1/30000 with respect to 5V
Analog filter Low-pass filter(-6dB/oct) Selectable from 3, 30, 300, and 1kHz.
Voltage output Input voltage cuff (For test point)
 
Drive power supply for UTMⅡ/UTMV
Power supply voltag DC24V *One UTMⅡ/UTMV at the maximum
 
Pulse input for rotation speed (open collector input)
Maximum input frequency In accordance with the output frequency of the UTMⅡ/UTMV series
Minimum input frequency 0.25Hz(15rpm)
Minimum detection pulse width 50μs
Circuit configuration No-voltage contact input (minus common)
Open collector connectable(Ic=Approx. 10mA)
 
Display section
Display Main display:Character height 15mm Numerical display by 7-segment green LED(5-digit+sign)
Sub display :Character height 8mm Numerical display by 7-segment green LED(5-digit)
Indicated value Main display:5-digit -99999~+99999 Signs: Minus sign on most significant digit
Sub display :5-digit -19999~+99999 Signs: Minus sign on most significant digit
Decimal point 0, 0.0, 0.00, 0.000(Only a torque and a power. Rotation speed is nothing)
Display frequency Selectable from 3, 6, 13, and 25 times/sec.
Status display HI/LO/HOLD
 
Setting section
Setting 
item
HI/LO limit:
HI limit /LO limit/Alarm HI limit/Alarm LO limit 

Comparison/hold:
Comparison function select/Near zero/Hysteresis/Hold function select/Detection time/Average sample number/Hold start level

Operation 1:
Motion detect (time)/Motion detect (range)/Zero tracking (time)/Zero tracking (range)/SI/F function select/Display frequency/Display ON/OFF

Operation 2:
Digital filter (torque)/Analog filter (torque)/Dead band/Digital filter (rotation speed)

Calibration:
Calibration function select 1(torque)/Zero calibration/Equivalent input calibration/Actual load calibration/Digital offset/Digital Zero limit/Calibration function select 2
(rotation speed/ power)

Protect/Initializ:
Setting protect/Key protect/Initialize/Password/Record data clear
Hold Sample, Peak, Valley, P-P, Average 
Hold section setting (All section・External signal・External signal + Time・Level + Time)
 
External input/output section
External input
(4)
Hold control/Hold reset/Digital Zero/Record data clear
Dry contact input circuit (minus common type), Ic=10mA or less
External output
(7)
HI/LO limit comparison(alarm HI・HI・OK・LO・alarm LO) /Hold complete/RUN
Open collector output circuit (sink type), Vceo=30V(max) Ic=30mA(max)
Interface
  • SIF:
  • 2-wire serial interface 
  •  
  • BCO:
  • BCD parallel data output interface (Option)
  •  
  • 232:
  • RS-232C communication interface (Option)
  •  
  • D3V:
  • D/A converter voltage output(3ch) (Option)
  •  
  • DAV:
  • D/A converter voltage output (Option)
  •  
  • DAI:
  • D/A converter current output (Option)
  • USB:
  • USB interface (Option)

 

※Only one option can be installed.

 
General performance
Power supply voltage AC100V~240V(+10%-15%)(free power source) 50/60Hz
Power consumption 14W max
Operating conditions Operation:-10~+40℃ Storage-40~+80℃
Humidity:85%RH or less(non-condensing)
Dimension 96(W)×96(H)×138(D) mm(Projections excluded)
Panel cutout size 92×92(+1-0)mm
Weight Approx. 1.0kg
 
Attachment
  External input/output connector ×1
AC input cord 3m(with solderless terminal)※ ×1
Cable for UTMⅡ/UTMV connection 2m ×1
Unit seal ×1
Connector for BCD output(with BCD output option) ×1
Operating tool(with D/A converter(3ch) option) ×1
Mini screwdriver(with D/A converter option) ×1
Operation manual ×1
*The attached AC input cord is intended for 100V AC power in Japan.